Sketchup compact kitchen appliances free#
Sketchup compact kitchen appliances windows#

If it varies, write down both the low and high measurements.Ĭheck your measurements. Ceiling heights, even in the same room, can sometimes vary by as much as several inches. Sometimes, especially with older homes, it is a good idea to take measurements in a few different areas of the bathroom. Measure the ceiling height and write it in the center of your drawing. In construction dimensions of an object are always given in the same format: width across the front, then height, then depth, so the dimension 32'x54'x14' is presumed to mean 32'w x 54'h x 14'd unless otherwise indicated.Measure from the second closest wall to the nearest point of the obstruction. Measure from the point on the wall that is nearest the obstruction to the point on the obstruction nearest the wall. Measure from the nearest wall to the nearest edge of the obstruction.Measure the distance of the object from the nearest two 90° walls. If the obstruction is not in contact with the floor, measure from the floor to the bottom of the obstruction. Measure the obstruction and record the width, height, and depth of the obstruction on obstruction reaches the ceiling, omit the height measurement.that you either cannot move or do not want moved. Draw boxes in your diagram to show the approximate location of any obstructions such as radiators, vents, pipes, exposed plumbing, smoke detectors, central vac., etc.Identify and Measure Unmovable Obstructions These measurements must Be 100% correct for your new cabinetry to fit correctly. Measure all appliances including stove, refrigerator, microwave,dish washer and sink.(This is important for us to present you with a proper design) Measure all walls even if you do not plan to put cabinets on them. Measure all other walls in kitchen following steps 2 through 12.

(In to or out of the room and which side the hinge is on) Indicate on your sketch how each door swings.If you haven’t already, measure the width of any doors, from outside of trim to outside of trim.Total the measurements from steps 7, 8, and 9. Measure from the floor to the ceiling.Measure from the top of the window to the ceiling and mark it down.

Then measure from the bottom of the window to the top of the window.

Sketchup compact kitchen appliances windows#

Measure from the floor to the bottom of your windows and mark it down.

Be sure to measure to the center of these and not the edge.

Mark on your sketch, the exact location of the sink, water and gas lines, wall switch and receptacles, and any other obstructions in the room.

They should equal the measurement in step 2. Go back and total the measurements from steps 3, 4, and 5.

Measure from that trim edge to the far wall.

Measure across the opening from outside edge of trim to outside edge of trim.

Go back and measure from the left corner to the edge of any opening, such as a window or door.

Write down the total measurement in inches.

Measure every wall, beginning at the left corner, to the far right corner.

Do indicate the precise location of the center-line of the current sink or plumbing.

Their placement in the new kitchen is part of the design process. However, take the measurements of any appliances you want to include in your new kitchen.

If you are replacing the cabinets, do include current cabinets or appliances in your measurements (width x height x depth).

For doorways with hinged doors, draw the door according to which way the door swings.

For example, if you measure a wall that is 10 feet, write it as 120 inches - a quotation mark (') denotes inches.

All of your measurements should be in inches.

Any photos you can take and send them along with your measurements. Photographs will always help your designer.

Sketchup compact kitchen appliances free#

Feel free to draw your ideas of what you would like and include the placement of your sink and appliances. Most people already have a good idea of where the major items will go in their kitchen. Remember this is just to get started, your designer will confirm details later. If you’re uncomfortable with precise measurements feel free to round to the nearest inch. Measure all the openings, from outside edge to outside edge. Record these letters as a key on your sketch.Īll you need is a tape measure, pencil and paper. In this sketch we’ll use areas “A” through “I”. Now, label all the openings in your kitchen. Be sure to include radiators or other obstacles that affect where cabinets can be installed. Mark any openings such as windows and doorways. Be sure to include any major structural features or obstacles. Draw your kitchen as a box showing all the walls that you think will have cabinets.